40 Watt Fluorescent Strobe Lamp Schematic

The circuit works much like the original Strobos. except that a fluorescent tube is used. Thus, the fluorescent tube zündbereit remains constant, the two electrodes of the tube are continuously transformer Ta1 supplied with electricity. This current makes the two resistance wires of the glow tube in, so the mercury evaporates into the tube and the electron emission is simplified. Ta2 Returns on the rectifier “D1-D4 , the voltage of the multivibrator, the ignition frequency of the tube is responsible for. The speed of the AMV is with potentiometer P1 set.
The pulse then passes through R3 to T3, is amplified there and controls the bias for the triac, the conducting of these alternates. If so, then the circuit through the tube and the ballast closes and the tube can light up. The pulses of T3 also enter via the capacitor C3 to the gate of the thyristor Th1. Simultaneously with the closing “of the circuit for the tube is Th1 -conductive and creates a short in the ignition coil current flow, which in turn generates a high voltage on the secondary. This voltage of several thousand volts is now operational on port J7 to a wire outside of the tube. The high voltage at the tube provides the necessary starting voltage so that it starts and can certainly light up until the thyristor Th1 locks again.

Part List:

C1/C2	2x		Elko standing 1μF/16V
C3	1x		Ker. Scheibenkondens. 0.1 μF
C4	1x		HV-capacitor 1μF 350V axial
C5	1x		Elko stand. 470μF 25 V
C6	1x		Poly condensation. 0.068 μF 630V
D1-4	4x		Diode 1N4001
D5	1x		Diode 1N4007
L1	1x		Ignition coil (such as the normal speed camera strobe)
P1	1x		Poti 6mm 2.2 M
R1/R4	2x		Resistor 470R 1 / 4 W
R2/R9	2X		Resistor 47K 1 / 4 W
R3	1x		Resistor 10K 1 / 4 W
R5	1x		Resistor 270R 1 / 4 W
R6	1x		Resistor 1.2 K 1 / 4 W
R7	1x		Resistor 22K 1 / 4 W
R8	1x		Resistor 120K 1 / 4 W
Si1	1x		Backup medium time 160mA
Si2	1x		A pair of fuse holders
T1/T2	2x		Transistor BC557B
T3	1x		Transistor BC547B
Ta1	1x		Transformer 2x 2x 5V 500mA 5VA
TA2	1x		Trafo 1,2 VA 9Volt
Th1	1x		Thyristor 4A 400V T0220
TR1	1x		Triac 4A 400V T0220

The points J1 and J2 to connect with the two electrodes on one side of the fluorescent tube. The points J3 and J4 , connect with the electrodes on the other side. Now stretch a thin insulated!! Wire along the tube and glue it eg. Scotch tape firmly. This wire carries the ignition voltage of several thousand volts to the tube so that they ignite properly. This wire, connect one end with J7 on the board, while the other end must necessarily be isolated. This wire leads except the high voltage pulses that is also voltage. The points with J5 and J6 of the board is one, tube fitting, ballast clamped to (choke, there’s the light trading.) Finally there is the voltage at J8 and J9. Now it should somehow already shine or flash, with the potentiometer, the flash rate can be set.